在隔熱斷橋鋁型材制造中，滾壓復合機是一種用于加工鋁型材的設備。它主要用于將鋁型材的兩個部分進行復合，通常是將隔熱斷橋鋁型材的外部鋁型材與內部隔熱材料（如塑料、橡膠等）進行復合。下面由有十多年的機器研發經驗的濟南歌德瑞斯機械設備為您帶來滾壓復合機的相關知識。

In the manufacturing of thermal insulation broken bridge aluminum profiles, rolling composite machines are equipment used for processing aluminum profiles. It is mainly used to composite two parts of aluminum profiles, usually by combining the external aluminum profile of thermal insulation broken bridge aluminum profiles with internal insulation materials (such as plastic, rubber, etc.). Below, Jinan Gede Ruisi Mechanical Equipment, with over ten years of experience in machine research and development, will bring you relevant knowledge of rolling composite machines.

　　1、操作者建議熟悉設備性能和安全規范操作方法。認識所需穿條型材大小面及相對應規格的隔熱條。

1. The operator must be familiar with equipment performance and safety regulations and operating methods. Understand the required size, surface, and corresponding specifications of insulation strips for threading profiles.

　　2、工作前應先檢查電源和氣路情況，和自動運行速度及三刀前后水平。

2. Before starting work, it is necessary to check the power and air circuit conditions, as well as the automatic operating speed and the level before and after the three knives.

　　3、檢查所需穿條型材有無變形，掉漆，劃傷，色差等缺陷，無問題后穿上對應隔熱條。

3. Check if there are any defects such as deformation, paint peeling, scratches, color difference, etc. on the required threading profile. If there are no problems, wear the corresponding insulation strip.

　　4、首先需根據型材需壓條位置調節刀具高度和上下距離，固定擱料升降輪。刀具調到正好與穿隔熱條槽口水平，轉動三個刀具壓力輪，壓緊型材。力度合適后固定緊。調節固定上面的三個輪，剛好貼上型材上面固定緊之后，試壓一支料。

4. Firstly, it is necessary to adjust the height and distance of the cutting tool according to the position of the profile pressing bar, and fix the material lifting wheel. Adjust the cutting tool to be exactly level with the groove of the insulation strip, rotate three cutting tool pressure wheels, and press the profile tightly. Fix tightly after the appropriate force is applied. Adjust and fix the three wheels on top, just press them tightly onto the profile, and then test a piece of material.

　　5、所壓好的型材建議是直的，抖動不變形，型材內腔完好。隔熱條無破損，型材無破損。

5. The pressed profile must be straight, shake without deformation, and the inner cavity of the profile must be intact. The insulation strip is undamaged, and the profile is undamaged.

　　6、機器運行時，操作者不得穿插機器前后，需調節建議停止運行才可穿行。

6. When the machine is running, the operator must not cross between the front and back of the machine, and must adjust to stop running before passing through.

　　7、手動調節試壓好后才可自動批量工作，并時常檢查所壓型材是否符合工藝要求。

7. After manually adjusting the pressure test, it can automatically work in batches and regularly check whether the pressed profiles meet the process requirements.

　　8、長時間離崗需關掉電源，運行發現故障問題建議停止工作，上報主管。

8. If leaving work for a long time, the power should be turned off. If any problems are found during operation, work must be stopped and reported to the supervisor.

　　9、設備每星期保養一次，加注潤滑油，檢查配套零件有無松動。

9. The equipment should be maintained once a week, with lubricating oil added and matching parts checked for looseness.

　　10、下班做好設備及周邊衛生，關掉電源。

10. After work, do a good job in equipment and surrounding hygiene, and turn off the power.

本文由 滾壓復合機 提供技術支持，更多的詳細精彩內容請點擊我們的網站  http://m.fuhuei.cn 我們將會全心全意為您提供滿意的服務。

This article is supported by the rolling composite machine technology. For more detailed and exciting content, please click on our website http://m.fuhuei.cn We will wholeheartedly provide you with satisfactory service.