復合機就是將兩層或者兩層以上的材料用粘合劑粘合成為一體。使原有材料得到新的功能。如薄膜和鋁箔、薄膜、紙張，無紡布等就經常會用到。亦可和膠片、海綿、布料等復合。常見的軟包裝材料基本上都是復合成品。下面由有十多年的機器研發經驗的濟南歌德瑞斯機械設備為您帶來穿條機的相關知識，我們應該如何歸零穿條機的壓盤數字呢？

A laminating machine is a process of bonding two or more layers of materials together with adhesive. Give new functionality to existing materials. Thin films and aluminum foil, thin films, paper, non-woven fabrics, etc. are often used. It can also be compounded with film, sponge, fabric, etc. Common flexible packaging materials are mostly composite finished products. Below, Jinan Gede Ruisi Mechanical Equipment, with over ten years of experience in machine research and development, will bring you relevant knowledge about threading machines. How should we reset the pressure plate number of the threading machine?

　　1. 將溢流閥松開，按下液壓?jiǎn)?dòng)按鈕，觀察電機旋向（從上方觀察電機應順時針?lè)较蛐D(zhuǎn)）。若方向不對，請調換三相線的相對位置。注意：本機工作壓力為10mpa，在出廠前已調好，非技術人員請不要調動壓力閥，以免出現異常，造成無謂損失。

1. Release the relief valve, press the hydraulic start button, and observe the direction of the motor rotation (the motor should rotate clockwise when viewed from above). If the direction is incorrect, please swap the relative positions of the three-phase lines. Attention: The working pressure of this machine is 10mpa and has been adjusted before leaving the factory. Non technical personnel should not adjust the pressure valve to avoid abnormalities and unnecessary losses.

　　2. 將面板上的聯動開關置“聯動”，將控制面板上的時間繼電器調整到一定時間，定位延時調為2s-3s，退刀延時調為3s-4s。

2. Set the linkage switch on the panel to "linkage", adjust the time relay on the control panel to a certain time, adjust the positioning delay to 2s-3s, and adjust the retraction delay to 3s-4s.

　　3. 工件安裝與調整：將裝好角碼的型材置于輔助定位器前方，45度接縫處的外角點對準定位器前面90度角的頂端。按型材高度調整主定位塊高度，使之與型材相適應。組角刀具的高度與型材連接的角碼高度相適應，當型材內側凸筋特殊時應更換主定位塊，使之能深入到筋間空腔內，不至于頂?shù)浇钌希虼酥鞫ㄎ粔K設計成活連接，以便用戶自行按型材配做各種定位塊。

3. Workpiece installation and adjustment: Place the profile with the corner code installed in front of the auxiliary locator, align the outer corner point at the 45 degree seam with the top of the 90 degree angle in front of the locator. Adjust the height of the main positioning block according to the profile height to match it. The height of the corner cutting tool is suitable for the height of the corner code connected to the profile. When the inner convex ribs of the profile are special, the main positioning block should be replaced to allow it to penetrate into the cavity between the ribs and not push against them. Therefore, the main positioning block is designed as a live connection, so that users can customize various positioning blocks according to the profile.

本文內容來自:穿條機 如果您想了解更多關于本行業知識請認準:http://m.fuhuei.cn，歡迎您的到來！

The content of this article comes from: threading machine. If you want to learn more about this industry, please take a look: http://m.fuhuei.cn Welcome to come!